1. Working environment　工作環境
1.1 Ventilation of the workplace 工作場所的通風
1.2 Sufficiently well ventilated by fresh or purified air - esp. in sandblasting and chemical area
工作場所要有新鮮和純凈的空氣，特別是有噴砂和有化學品的場所。
1.3 Ventilation systems or windows or other openings should be available
必須有通風系統，窗戶或是其它通風渠道。
1.4 Temperature of workplaces　工作場所的溫度
1.5 Thermometers should be provided so that temperature can be checked
工廠要有溫度計以方便測溫
1.6 Temperature should be kept at an appropriate and comfortable level to work in
工作時溫度需保持在合理且舒適的水平
1.7 Lighting at the workplace 工作場所的光線
1.8 Suitable and sufficient light levels are required as follows:
1.9 500 LUX for operating/working activities　工作場所是500 勒克斯
1.10 750 LUX for the inspection activities　　 檢查場所是750 勒克斯
1.11 Noise at work 工作噪音
1.12 Noise levels shoud be below 85 dB　噪音低于85 分貝
1.13 If above, workers should be informed and offered ear protection
高于85分貝，通知工人并提供耳朵保護設施。
1.14 If above 90dB, ear protection is compulsory while warning signs displayed
高于90分貝，必須提供耳朵保護設施，同時做出警示標志。
1.15 Minimum space requirements　最小空間要求
1.16 Every workroom should have not less than 8 cubic meters per worker, not taking into account space 3 1.17 meters from the floor　每個工作間，每個工人至少8立方米，層高3米。
1.18 Work stations　工作場所
1.19 Working area and place must be arranged so that work can be carried out in a safe environment.
工作區必須是安全的環境。
1.20 Ergonomic principles have to be taken into account　考慮人體工程學的原理。

1.21 Seats must be suitable and safe for the user　座椅必須合適安全

C&A驗廠對設備安全的要求

砸扣機器要有適當的保護裝置。參見砸扣保護器
adequate protective device at snap button machines

在操作砸扣機器的時候，要有適當的保護程序。參見砸扣保護器
adequate PPE provided / used when operating snap button machines

在使用直刀型電剪刀和帶刀型凈裁機時要佩戴金屬手套。參見金屬手套和凈裁機。
metal gloves provided / used when operating the vertical cutter / blend knife

在使用模型沖切機時，不能只有一個開關。
Die cut machines operated with not only one switch button

以上要求工廠必須認真檢查執行，有不足處要立即改正。

以下是驗廠的基本要求，包括工廠必備的設備以及品質管理的系統。
驗布機，驗布系統，驗布記錄。
Fabric inspection M/C, fabric inspection system (4.0), and fabric inspection report

中期驗貨報告
In-line inspection report

終期驗貨報告
Supplier Final inspection report

自動洗衣機和洗衣粉（參考歐洲市場標準），多纖維布（ＩＴＳ檢驗行可購）
Automatic washing M/C (similar with our inspection centre), washing detergent ( similar with Europe market, such as Persil ), Multi- fabric ( can buy from ITS )

室內測試報告
in-house test report

驗針機
Needle detect M/C

斷針控制系統和記錄
Broken needle control system and report
剪刀控制系統和記錄
Scissors control system and report.

防線跡起皺檢查表
Check list to prevent seam puckering

光線要求，操作區500LUX, 檢查區750LUX
Lighting according to Socam requirement.
Operating area 500Lux
Inspection area 750Lux